JurassicJeep.com
About  |  Jeep #12  |  Jeep #18  |  Jeep #29  |  Reference  |  Shop  |  Forums

Posts Tagged ‘Foglights’

Jeep #29: Wiring up Lights & In Cab Winch Controls

When I installed the rear fog lights, I did not wire them into the vehicles electrical system.  I wanted to wait until i had fully planned out my electrical system before tackling this job, so I only had to do things once.  The default Jeep rocker switches fade badly over time.  They might have looked nice when the Jeep was new, but no more…  My front fog switch looked like this:

Stock Rear Fog Switch

Stock Rear Fog Switch

I decided I not only wanted to install a rear fog switch, but also replace this old faded thing!  I looked around for alternatives, and finally found switches I really liked.  They are Carling Contura V Laser Etched switches.  These switches are sealed switches originally for marine applications, so not only are they great looking, they should last a long time, and bonus they are resistant to water, being rated at 30 minutes submersion under 1 meter of water!  They are a little expensive, but you can get tons of different options on the switch face, and color of illumination, and as John Hammond would say “Spared no expense”.

The stock mounting panel, seen with the switch in the photo above, has 3 switch cutouts already, only the surface material covers them, so I knew I wanted to install my new rear fog light switch adjacent to the existing front fog switch.  Hmm? What to do with the third switch location.  I decided to add an in cab winch control.

With decisions made on the switches I had to plan out the wiring.  Complicating matters is that after I installed the front fog lights, the stock headlight switch was showing its age and wasn’t dealing well with the new fogs.  The YJ has the front fogs wired such that they are controlled through the headlight switch.  The stock front fog lights will only work with the headlights on, but not the high beams.  After I installed the front fogs, I was testing them , and after a few minutes all the jeep lights would shut off for a bit, and then turn back on.  When I researched what was going on, turns out the headlight switch, when it gets old can’t deal with the extra chore of controlling the fog lights and headlights.   So I decided I would wire the front fogs independent of the headlight switch, so I could actually use them, and could use them no matter if I had the headlights on low, high or off.

My final switch wiring thus needed to be:  An ignition controlled power feed, so the switches only work when the ignition is on, A power feed for when the dash lights are on(to control the switch lights), ground wire( for the lights in the new switches), a front fog control wire(low voltage, that feeds a relay), a rear fog control wire(low voltage, that feeds a relay), A winch in control, and a winch out control (both controlling the winch solenoid).  Its a pretty good bundle of wires, and the power and ground feeds need to go to each switch.  I wired this up and made a mini harness, with a 9 pin plug. (7 wires, 2 extra spaces just in case 🙂

Switch Harness

Switch Harness

With the Harness made, it was a matter of running all the wires in the jeep to all the proper locations, and tapping into the correct lines.  Very time consuming task, but when finished I was able to feed the new wires either into existing wiring looms or where I had a lot of wires (running through the engine bay, I added a new run of split loom, so it looks like it belongs there, and keeps the wires safe.  With all of that finished, I wired these into the other side of the plug, so I can now unplug the switch panel if I ever need to work on it, or if I need to get into the dash for any reason.  With it all connected, I tested it and it all worked, so I reassembled everything.  Here are the final results.  Excuse the dirty dash as the Jeep hasn’t had a spring cleaning yet, its dirty from sitting most of the winter!

Switches Installed

Switches Installed

Switches Illuminated

Switches Illuminated

Jeep #29: Finishing Up Details

I’ve been tinkering with the jeep over the past 2 months, and hadn’t had a chance to update my progress here.  Mainly having fun during summer driving the jeep!!!

Keen eyed observers may have noticed on the jeep trip photos I posted, there was a winch installed and the rear fog lights were installed.  So, let me backup and cover those first.

Rear Fog Lights: The original KCs can be hard to find, but a couple show up on ebay every so often.  I decided to go with new lights that are almost duplicates of the original KC lights.  They are by a company called Eagle Eye lights, they are the correct size and color, BUT they come in a chrome housing instead of black.  The ones I choose also had a thick plastic lens ring with louvers.  I removed the louvers from the lens ring and I used spray plastidip to convert the chrome housing into black.  The results look almost identical to the KC lights.

light2s

Winch: I knew I wanted a new winch instead of the 20 year old ramsey winches from the movie.  I read reviews and decided the superwinch lp8500 had good reviews and would look very similar to the Ramsey after I moved the winch solenoid.  At $300 it also came with the correct hawse fairlead instead of a roller fairlead so many winches come with.  I bought the winch mounting plate NOT made specifically for a YJ.  The mounting plate I bought would bolt right up to most trucks, But not the YJ.  I choose this mounting plate because it looked like the ones from the movie.  My neighbor has a drill press, so adding the holes to align with the YJ mounting holes for the tow hooks(which of course needed removal) was pretty easy.    Here you can see what the winch looked like during the offroading trip with the solenoid in the “from manufacturer” location.

winchtrip

Correct BFG All Terrains:  My old tires were at end of life, so it was time to get these as well.  New BFG All terrains from the local Discount tire in 235/75/15 size.

The BFGs and the winch were literally done in the last 3 days before our offroading trip.  I didn’t want to chance my old tires, or getting stuck, so it was as good an excuse as any to get those parts off my checklist.

Since that trip I have also completed the last items as well.

Remote mounting the winch solenoid:  I started this project hoping I could get it done in a day, but alas things went awry!  Mainly the fact that the auto parts stores by me only stock 4 guage cables, and the winch needs 2 guage.  I started by taking the solenoid off and figuring out where under the hood it would fit.  It fits very well over the wheel wheel in front of the stock jack.  I created some brackets from building brackets from the hardware store, and then I found a place online that deals mainly in batteries (marine and otherwise) and they made me up the custom cables I needed.  While waiting for the cables to come in from my online source I painted the bracket and installed the solenoid box, so all I would need to do was hookup the cables when they arrived.  (below pic is waiting for cables to arrive)

solenoid

To remote mount the superwinch solenoid you need 3 cables from the solenoid box to the winch.  I went ahead and also ordered a replacement for the original postive cable from battery to solenoid just to remove all the excess you see in the picture above. All cables need to be 2 guage (straight from the superwinch help line). Once the cables arrived the hookup was a cake walk.

Stock Front Fog Lights: I tried to order original equipment Chrysler/Jeep Fog Lights.  A website dedicated to factory parts listed them as available and also the special angle bracket.  But after placing an order and waiting 2 weeks, I got an email that these parts were no longer available and my $$ had been refunded.  Drat!  However I knew Delta makes some fog lights very similar to the stock original ones (delta 100 clear fogs with the stone guard).  But what about the brackets.  I could simply put a hole through the bumper and bumper mount them, but the originals sit back a little, and I like that look.  My neighbor offered to bring me home some brackets from his machine shop, so I gave him a template, and he delivered brackets about a week later.  Luckily the original fog light wiring was still under the bumper(since this was a sahara and someone had removed the fogs at some point), so wiring them up was simple, and the brackets my neighbor made fit perfectly.    Here is how the Jeep front looks now with the fogs and winch solenoid gone.  DSC_0016sThe old bumper ends were in bad shape and since the brackets to hold the fog lights attach to the same bolts, I also replaced those while I was doing all of the above.  I may need to repaint the bumper now as it looks a bit faded next to the new parts.

Mopar Light Bar:  The light bar for JP 29 has no light tabs and appears to be a solid piece (the originals may have been 3 piece bars, but during painting they may have filled the seam up, while removing the light tabs and painting it).  I had found a light bar on Craigslist, but it was for a TJ, so the mounting holes were wrong, and it had light tabs and was a bit rusty.  Instead of altering it, I opted to find a fab shop to make my light bar, by simply copying the one I had, and leaving off the light tabs.  Removing the old windshield bolts took a ton of work as they were seized up badly, one even needed an easy out after it sheared off.  The fab shop did a great job copying the one I had, and after priming and painting(with plastipdip), I got that installed as well.

DSC_0024sSo Jeep #29 Is now 100% complete.

It still has shiny metalflake vs correct low gloss base color, and the red is all plastidip right now.  When the stars align correctly I will be repainting her, until then its all about the fun!

Jeep #12: New Foglights Installed

Finally got around to installing the new Delta 150 foglights on the front bumper. They actually match the original Jurassic Park lights pretty closely as long as you can get the old style light guards like I managed to get. They have a very similar cross hatching.

In order to get them to fit on the front bumper, their brackets needed to be turned around. This gives them enough clearance to clear the fender horns.

To test out the new foglights, I drove the Jeep…. like this:

Jeep #12: To-Do List

The body is amazingly almost completely rust free. The frame however is not so lucky. The front and rear sections are common for rusting, and they did. The front was already repaired, and the rear will be done. I suspect the frame is probably 60% there.. there is a lot of surface rust.

Here is the current to do list, with parts stacking up:

-Install Steering Stabalizer
-Install Sway Bar Bracket
-Install Bump Stops
-Install Shocks
-Install Pads / Rotors
-Install Rear Drums
-Install new TC Output Seal
-Change Oil in TC and Transmission
-Repair Rear Frame Rust
-Remove / repaint Front Bumper
-Install Bumper Guards
-Install Foglights on stock brackets (clean / paint brackets).
-Install Rear Foglights and wire in switch.

I should have front fenders, half doors and (now) a windshield frame on the way. I might pick up some paint to start laying down as a protectant. It really needs to stop raining for me to get some of these things done.

Jeep #12: Collecting Parts

I found frame repair sections. There were some expensive ($250) sections that were boxed in, or some cheaper ($100) plates that you weld to existing metal. I opted for the cheaper ones as there is still plenty of metal to secure to.

I haven’t driven the Jeep since the day I bought it (Thursday) because the battery went dead. I wasn’t happy with the battery connections (they were old and rigged in there) so I worked a bit today to replace them. In the process of doing that I had a rusted stud that refused to come out, so I had to cut a wire. I could have been driving the Jeep today if that had gone smoothly.

The last few days have spent scouring information on JeepForum, this JP site and on parts supplier sites. I have spent quite a bit of money on some parts that I need / wanted such as:

-Rear Fog Lights (The amber driving lights). I went with the Pro Comp 100 4″x6″ amber fog light. I will be replacing the bulb with a lower wattage lamp and then wiring a flip switch to allow for switching between red and amber.

-Front Fog Lights. One of mine was missing the lense / reflector assembly. Replacing this with a factory one would have cost quite a bit of money. I decided to go with the Delta 150 Foglight. It is a pretty close match for the factory light, just a little bit thicker I presume.

-Fenders. I found a company that claims the fenders they sell are OE quality. If they are not, I will be returning them and attempting to get my money back.

-Soft Top. I managed to find a Spice Bestop top here on Craigslist locally. It has quite a bit of hardware (2 of everything) and a decent top. I picked it up for $200 which is a great deal.

Looking for:
-Half Doors. Saw some on eBay, probably will be out bid even though they are up to $400 right now.
-Windshield Frame. I really don’t want to buy a aftermarket steel frame. I am trying to find a used rust free frame. Currently bidding on one, but its already up past where I really want to pay.

Future Steps:

I have a bit of maintainence to do. Hopefully I can get it all done tomorrow. I have the battery, steering stabalizer strut, rear axle seals, TC output seal, and fluid changes for those.

Now that I have a soft top, I want to pull off the Hardtop and install the soft top hardware. That will require a lot of cleaning and painting of the parts as some of them are rusty. I hope there is enough components to make atleast 1 good set of hardware.

But before I put the soft top on, I want to pull the rollcage, seats and carpet and Herculine the floors and interior. I am pretty sure my floors are rust free (atleast no holes). So I want to keep it that way. I figure 3-4 coats of Herculiner should do the trick. After that is done the carpet will go back in. (I really like that look of that!).

Jeep #18: Coming Together

Bought a pair of rather generic foglights with plastic grating over them today.

Got the interior door panels in and secured.

Cleaned and primered the fenderflares just as it started pouring rain again.

Hoping hoping hoping to be done mid-week.

© 2010 - 2024 Jurassic Jeep - Created by AJ Quick - Jurassic Park is a Registered Trademark of Universal Studios & Amblin Entertainment, Inc